Hull and structural surveys. Model course 3.07. Compendium - Volume 2

Издание на английском языке
This book is a comprehensive guide to conducting marine surveys and inspections of ships, covering various stages of ship construction, operation, and maintenance. It details standards and procedures for inspectors, including preparation for surveys, key definitions, methods for identifying deficiencies, and specific instructions for surveying ships at various stages, from construction to scheduled repairs and condition assessment. The book contains numerous practical materials, including checklists, report forms, and recommendations from the International Association of Shipping (IACS).
В продаже также есть Hull and structural surveys. Model course 3.07. Compendium - Volume 1 и Hull and structural surveys. Model course 3.07

Content
01 General
01-01. Standard procedures to be followed by the surveyor
01-02. Basic definition
01-03. Identification of a substandard vessel
01-04. Preparation for surveys
01-05. Surveyor's glossary
Appendix 1. (IACS REC72)
Appendix 2. (IACS REC82)
02. Surveys during construction
02-01. Objective and application
02-02. Inspection record for ships under construction (Hull)
02-03. Survey at assembly processes
02-04. Survey of hull blocks (assembly unit)
02-05. Survey of rudder
02-06. Survey at processes of block loading
02-07. Final inspection of hull construction
02-08. Water-tight test and hydrostatic test of hull parts
02-09. Non-destructive inspection of welded joints of hull
02-10. Pressure test of pipes (Hull part)
02-11. Rudder installation
02-12. Keel alignment/flatness and measurements of principal dimensions
02-13. Inspection of load line marks and draft scales
02-14. Bilge suction test
02-15. Closing appliances for various openings
02-16. Inspection of bulwarks, guardrails, freeing arrangements and gangways
02-17. Inclining test
02-18. Stability information, loading manual and loading computer
Appendix 1. Inspection records of new construction (Hull)
Appendix 2. Investigation record for quality control condition of shipyard
Appendix 2. Figures
Appendix 3. Check list for classification survey during construction (Hull)
Appendix 4. IACS Requirement S14 Testing procedures of watertight compartments
Appendix 5. IACS Recommendation No.20 Guide for Inspection of ship hull welds
Appendix 6. IACS Recommendation No.31 "Inclining test unified procedure"
Appendix 7. IACS Recommendation No.48 "Recommendation on loading Instruments"
03. Maintenance survey, assessment and repair
03.-A. Guidance for class maintenance surveys
03A-01. Survey application
03A-02. Preparation for survey
03A-03. Attendance to surveys
03A-04. Maintenance and presentation of documents
03A-05. Survey Items
03A-06. Enhanced survey programme
Table 1. Class survey (SS, IS, AS)
Figure 1. Suspect Area & Substantial Corrosion
Table 1-1. Internal Examination and pressure test for spaces and tanks required at periodical surveys
Table 2. Class Survey (Docking survey)
Table 3. Class Survey (Boiler survey)
Table 4. Class Survey (Propeller shaft and stern tube survey)
Appendix 1. Thickness measurement and close up survey at each Special survey
Appendix 2. Suspect areas
Appendix 3. Additional thickness measurement
Appendix 4. Thickness measurement and close-up survey at Intermediate survey and annual survey
03-B. IACS Guidelines for surveys, assessment and repair of hull Structure - general cargo ship
03-C. IACS Guidelines for Surveys, assessment and repair of hull Structure - bulk carrier
Appendix 1. IACS Requirement Z3 "Periodical survey of the outside of the ship’s bottom and related items"
Appendix 2. IACS Requirement Z4 "Survey of hatch covers and coamings"
Appendix 3. IACS Requirement Z7 "Hull classification surveys"
Appendix 4. IACS Requirement Z8 "Corrosion protection coating for salt water ballast spaces"
Appendix 5. IACS Requirement Z9 "Corrosion protection coating for cargo hold spaces on bulk carrier"
Appendix 6. IACS Requirement Z13 "Voyage repairs and maintenance"
Appendix 7. IACS Requirement Z22 "Survey requirements for automatic air pipe heads"
Appendix 8. IACS Recommendation No.39 "Guidelines for use of Boats or rafts for close-up survey"
Appendix 9. IACS Recommendation No.77 "Guidelines for the surveyor on how to control the thickness measurement process"
Appendix 10. IACS Recommendation No.78 "Safe use of portable ladders for close-up surveys"