Yanmar 2GM20(F)(V)(C), 3GM30(F)(V)(C) Operation manual/Инструкция по эксплуатации Yanmar 2GM20(F)(V)(C), 3GM30(F)(V)(C)

Издание на английском языке
This Operation Manual describes the operation, maintenance and inspection of the 2GM20(F)(V)(C), 3GM30(F)(V)(C) Yanmar Marine Diesel Engines.
Read this Operation Manual carefully before operating the engine to ensure that it is used correctly and that it stays in the best possible condition.
Keep this Operation Manual in a convenient place for easy access.
If this Operation Manual is lost or damaged, order a new one from your dealer or distributor.
Make sure this manual is transfered to subsequent owners. It should be considered as a permanent part of the engine and remain so.

Contents
Warning Symbols
Safety Precautions
Safety Precautions for Inspection
Product Explanation Use, Driving System, Etc.
Detail of Name Plate Engine Specifications
Direct Seawater Cooling Type, GM Series
Fresh Water Cooling Type, GMF Series
Direct Seawater Cooling Type, GMV Series
Fresh Water Cooling Type, GMFV Series
Direct Seawater Cooling Type, GMC Series
Fresh Water Cooling Type, GMFC Series
Names of Parts
Non Operation Side
Operation Side
Major Servicing Parts
Control Equipment
Control Panel
Controls And Equipment
Alarm Equipment
Alarm Devices
Single Lever Remote Control Handle (Morse Type)
Stopping Equipment
Decompression Equipment
Operation
Fuel Oil, Lube Oil, And Cooling Water
Selection of Fuel Oil
Handling of Fuel Oil
Lube Oil
Cooling Water
Selection of Engine Lube Oil
Handling the Lube Oil
Before Initial Operation
Supply Fuel Oil
Supply Engine Lube Oil
Handling of Cooling Water
Supply Clutch Lube Oil
Supply Cooling Water (for Fresh Water Cooling Type Only)
Marine Gear Oil Capacity
Cranking
Fresh Water Cooling Capacity
Manual Operation (Seawater Cooling Only)
Check And Resupply Lube Oil And Cooling Water
Operating Your Engine
Electric Operation
Inspection Before Starting
Checking And Resupplying Fuel Oil
Checking And Resupplying Engine Lube Oil
Checking And Resupplying Clutch Lube Oil
How To Start the Engine
Checking the Remote Control Handle
Checking the Alarm Devices Electric Operation
Preparing Fuel, Lube Oil, And Cooling Fresh In Reserve
Restarting After Starting Failure
Air Venting of the Fuel System After Starting Failure
Fuel System Air Venting Procedures
After the Engine Has Started
Engine Acceleration And Deceleration
forward-Neutral-Reverse Clutch
Cautions During Operation
Racing the Engine
Stopping the Engine
Long Term Storage
Fresh Water Cooling
Cooling Water Drain Cocks
Maintenance & Inspection
General Inspection Rules
List of Periodic Inspection Items
Inspection On Initial 50 Hrs. of Operation
Inspection Every 50 Hours
Replacing the Engine Lube Oil And Lube Filter (1st Time)
Replacing the Clutch Lube Oil (1st Time)
Adjusting the Remote Control Cable
Inspection Every 150 Hours
Inspection Every 300 Hrs
Replacing the Fuel Filter
Adjusting the Tension of the Cooling Water Pump Driving Belt
Inspection Every 600 Hrs.
Inspecting And Replacing Anticorrosion Zinc
Inspecting Inner Parts of the Seawater Pump
Replacing Fresh Water Cooling
EPA Requirement
EPA Certification Plate
Inspection And Adjustment of Intake/Exhaust Valve Clearance
Inspecting And Adjusting the Fuel Injection Spray Condition
Attachment Position for Certification Plate
Conditions To Insure Compliance With Emission Standard
Warranty Period for Emission Parts
Inspection And Maintenance
Emission System Warranty Statement
Trouble And Troubleshooting
Consulting Your Yanmar Dealer And Distributor
Warranty Service
Piping Diagrams
Wiring Diagrams
Appendix A
11-1 2GM20 Piping Diagrams
11-1 3GM30 Piping Diagrams
11-1 2GM20F Piping Diagrams
11-4 3GM30F Piping Diagrams
11 -5 2GM20V Piping Diagrams
11 -6 3GM30V Piping Diagrams
11 -7 2GM20FV Piping Diagrams
11 -8 3GM30FV Piping Diagrams
11-9 2GM20FC Piping Diagrams
11-10 2GM20C Piping Diagrams
11-11 3GM30FC Piping Diagrams
11-12 3GM30C Piping Diagrams
Appendix B
Wiring Diagram
12-1 for the A-Type Instrument Panel
12-2 for the B-Type Instrument Panel